In this video I'll show you how to test what your klipper controlled 3d printer can do and show you how to set a limit for your acceleration to avoid print defects at higher speeds.

*Since recent firmware change, it is necessary to issue a 'restart' command after changing any settings or following any calibration procedures.*

Ringing Tower stl: https://www.klipper3d.org/prints/ring...

Commands to copy & paste

Zero Pressure advance:
SET_PRESSURE_ADVANCE ADVANCE=0

Acceleration Test (1500mm/s start):
TUNING_TOWER COMMAND=SET_VELOCITY_LIMIT PARAMETER=ACCEL START=1500 STEP_DELTA=500 STEP_HEIGHT=5

Acceleration Test (7500mm/s start):
TUNING_TOWER COMMAND=SET_VELOCITY_LIMIT PARAMETER=ACCEL START=7500 STEP_DELTA=500 STEP_HEIGHT=5

Acceleration Test (6000mm/s start):
TUNING_TOWER COMMAND=SET_VELOCITY_LIMIT PARAMETER=ACCEL START=6000 STEP_DELTA=500 STEP_HEIGHT=5

Affiliate links (If you purchase something after clicking any of the below links I may earn a small commission at no cost to you. This is a great way to support the channel)

*Creality Sonic Pad*
UK: https://www.geekbuying.com/go/7TPdqKOx
US: https://www.geekbuying.com/go/7TPdvEYU
Everywhere else: https://www.geekbuying.com/go/7TPawLUl

Discount Code: NNNCRESONPAD

Amazon
https://amzn.to/3AiYtwD
Discount code: 10NTDPJE

*Other Sonic Pad Videos*

Sonic Pad Review:    • Creality Sonic Pad - The Easy Klipper...  

Sonic Pad Basic Series
Part 1 - Connecting to a Creality 3D Printer:    • How To Connect A Creality 3D Printer ...  
Part 1a - Connecting to a non-Creality 3D Printer:    • How To Connect A Non-Creality 3D Prin...  
Part 2 - Completing initial setup:    • Completing The Initial Setup Of The S...  
Part 3 - Starting a print and UI Tour:    • Starting A Print With A Sonic Pad And...  
Part 4 - Controlling remotely and WEB UI:    • How To Control Your Sonic Pad Remotel...  
Part 5 - Connecting a camera and tinelapse videos:    • How To Connect  A Camera To Your Soni...  

Sonic Pad Intermediate Series
Part 1 - PID Tune    • How To PID Tune With The Sonic Pad - ...  
Part 2 - E-Steps/Rotational Distance    • How To Tune E-Steps/Rotational Distan...  
Part 3 - Slicer Settings    • Slicer Settings and Profiles With Cur...  
Part 4 - Sending Prints From Slicer/Images On Screen    • How to Send Files To Your Sonic Pad A...  
Part 5 - Input Shaping -    • Tune Input Shaping With The Included ...  
Part 6 - Pressure Advance -    • Video  
Part 7 - MACROs -    • Video  
Part 8 - Max Acceleration -    • Maximum Acceleration Test (How Fast C...  
Part 9 - Mid-print Filament Change -    • How To Complete a Mid-Print Filament ...  

Other
Firmware Update September '23 -    • Creality Sonic Pad Firmware Update - ...  
Creality Sonic Pad - How To Update Firmware Without Losing Everything! -    • Creality Sonic Pad - How To Update Fi...  


..............................................................................................................................................................

BUY ME A COFFEE
If you're enjoying my content, why not consider supporting the channel by buying me a coffee?
Even very small amounts are greatly appreciated and re-invested into bringing you better content.

https://www.buymeacoffee.com/rickyimpey

You can also use the YouTube 'Thanks' button above if you prefer.
...............................................................................................................................................................