This is a 3D Printed Eclipson Model C. In this video I will show step by step how to assemble and paint this airplane. From roles of LW-PLA to full flying RC airplane. Links bellow to all materials and parts. During the assembly of this plane I made a mistake with the tail wheel assembly. The tail wire should not be glues to the lower rudder. There should be a bend right at the tail fitting STL part so that the impact of the tail wheel will be on the end of the fuselage and not on the rudder hinge. I will show the correct way of assembly on my Maiden flight video.

Thank you so much for watching!

If you like videos like this, consider buying me a coffee, it really supports me:
https://www.buymeacoffee.com/troymcmi...


See what else I am working on:   / troymcmillan_rc  
https://www.tiktok.com/@troymcmillan_...
#3Dprinted,#RCairplane, #ItFlies

STL Files: https://www.eclipson-airplanes.com
Artillery Sidewinder 3D Printer: https://amzn.to/396eqIp
Artillery Genius 3D Printer: https://amzn.to/39cA6CZ
LW-PLA: https://colorfabb.com/lw-pla-natural
varioShore TPU: https://colorfabb.com/varioshore-tpu-...
White PLA: https://amzn.to/3ghcHl1
Black PLA: https://amzn.to/30E4YIT
TPU: https://amzn.to/2Sw3Oe8
AR620 Receiver: https://amzn.to/3j4PbK4 DX6
DX6 Transmitter: https://amzn.to/3l6NFsD
2212-13 1400KV: https://amzn.to/2P13PYU
8x6 Propeller: https://amzn.to/36cf3yL
1000mAh Battery: https://amzn.to/353cLmf
450mAh Battery: https://amzn.to/3k4lY1J
4x 9g servos: https://amzn.to/31kj82B
10x5x3mm Magnets: https://amzn.to/3bLcrMB
2x8mm Screws: https://amzn.to/3p8gmqY
1mm Carbon rods: https://amzn.to/32lEoW2
80mm foam tires: https://www.amainhobbies.com/dubro-3....
small 40mm Foam Wheels: https://amzn.to/2Ie853O
1/8” Wheel Collar: https://amzn.to/3p4tvl1
3pin wire assortment: https://amzn.to/3l1xNYt
XT60 connector: https://amzn.to/3iyZWnf
2mm push rod ends: https://amzn.to/3nnjD4U
Z-Bend pliers: https://amzn.to/34mA0rt



Print Settings for LW-PLA
Quality:
Layer Height – 0.25
Line Width – 0.4
Shell:
Wall Line Count – 1
Z Seam Alignment - User Specified
Z Seam Position - Front (Rotate model to have best Location for seam)
Seam Corner Preference - Expose Seam
Infill:
Infill Density – 0
Material:
Printing Temperature – 235
Build Plate Temperature – 60
Flow – 53%
Speed:
Print Speed – 100
Outer Wall Speed – 55
Inner Wall Speed – 55
Travel Speed – 100
Travel:
Combing Mode – off
Enable Retraction – Checked
Retraction Distance – 3 (Stringing cannot be eliminated with LW-PLA)
Retraction Speed – 10mm/s
Retraction Extra Prime Amount – 0.3
Cooling:
Enable Print Cooling – Checked
Fan Speed – 100
Minimum Layer time - 5
Mesh Fixes:
Union Overlapping Volumes – Checked
Special Modes:
Surface Mode – Normal
Experimental:
Slicing Tolerance – Middle



Disclaimer: I am sponsored by some of the products I mention. However, all of my opinions are my own. Some of the above links are affiliate links, that does not effect the price you pay for a product, but I may receive a small commission if you make a purchase. This helps support my channel and allows me to continue to make videos like this. Thank you for your support!!